Before and after cleaning of a walkway by H2O Pressure Washing

Do Pavers Need New Sand After Pressure Washing?

November 22, 2026

Often, yes. Cleaning pavers properly removes loose, dirty joint sand along with the algae and weeds living in it, so the joints usually need to be refilled afterward. Replacing that sand keeps the pavers locked together, slows weeds and ants, and gives a sealer something stable to bind to.

What the sand between pavers actually does

Paver joints are not decoration. The sand packed between each paver locks the whole surface together so it moves as one piece. Without it, individual pavers can rock, shift and settle unevenly under car tires and foot traffic.

Over time that joint sand gets dirty. It collects organic debris, holds moisture, and becomes a seed bed for weeds and a home for ants. On pool decks and patios it also traps algae, which is a big part of why pavers look green and slick in the corners. Near the coast in Ponte Vedra, wind blown sand and salt air add to that buildup.

Why cleaning pulls sand out of the joints

A thorough clean has to get into the joints, because that is where the growth lives. Surface cleaners and rinsing will lift loose and contaminated sand out with the dirt. Leaving it in place would mean leaving the weeds, ant colonies and algae roots that make pavers look tired again within weeks.

So some sand loss is normal and expected, not a sign of a careless job. The question is what happens next. Pavers left with half empty joints can shift, and gaps fill up with whatever blows in, which tends to be seeds and organic debris.

Regular sand vs polymeric sand

There are two common choices. Regular paver sand is cheap and easy to sweep in, but it washes out with every heavy storm and does little to stop weeds. In a place with summer downpours most afternoons, it rarely stays put for long.

Polymeric sand is mixed with binders that harden after being lightly wetted. Once cured, it stays in the joints through rain and resists weeds and ants far better. It does need the pavers to be clean and the joints dry when it goes in, which matters in our humidity. Installing it on a damp surface, or leaving a haze of it on the paver faces, causes problems that are hard to undo.

How re-sanding fits with paver sealing

If you plan to seal, the order matters: clean, re-sand, let everything dry fully, then seal. Sealer helps lock the joint sand and protect the paver surface, but it will also lock in whatever is underneath. Sealing over dirty joints or damp sand is a common cause of a cloudy, blotchy finish.

H2O Pressure Washing is certified in paver sealing, and our concrete cleaning services include paver cleaning and sealing. For a full look at whether sealing makes sense for your home, read why paver sealing is worth it in Northeast Florida.

Signs your pavers need sand now

Look for joints you can see down into, pavers that rock when you step on an edge, weeds growing in straight lines along the joints, and little piles of sand from ant activity. On driveways, watch for pavers settling where tires turn. Any of these means the joints need attention, ideally right after a good cleaning.

Pool decks deserve extra attention because water splashes and drains across them constantly. Our post on cleaning pool decks, lanais and screen enclosures covers what else to watch for around the pool.

Frequently asked questions

Is it normal to lose sand when pavers are cleaned?

Yes. A thorough clean removes loose, dirty sand along with the growth in it. That sand should be replaced so the pavers stay locked together.

Should I use polymeric sand or regular sand?

Polymeric sand holds up much better through Florida rain and resists weeds and ants. It needs clean, dry joints when it goes in.

Can I seal pavers without re-sanding?

You can, but sealing over half empty or dirty joints locks in the problem. Cleaning, re-sanding, drying and then sealing gives the most even result.

How long should pavers dry before polymeric sand?

They need to be fully dry, which can take longer than expected in humid weather. Installing sand on damp pavers can leave haze and weak joints.

Who cleans and re-sands pavers in Ponte Vedra, FL?

H2O Pressure Washing cleans and seals pavers in Ponte Vedra and across St. Johns County. Call (904) 506-7656 for a free quote.

Get a free estimate in Ponte Vedra, FL

H2O Pressure Washing is a family-owned pressure and soft washing company based in St. Johns, FL, serving St. Johns County, Jacksonville and Clay County. Call (904) 506-7656, see the service, or request a free quote. More answers on the H2O blog.

Back to Blog
H2O Pressure Washing · Saint Johns, FL

Want a quote for your property?

Family-owned, based in Saint Johns, FL, with 10+ years in St. Johns County. Send the form below, or call or text a few photos and we will get you a free, no-obligation quote.